Tono LPC XL 01 – Extra-Large Full-Motion TV Wall Mount, 130″ / 150 kgs

The Tono LPC XL 01 is an extra-large full-motion TV wall mount engineered
for the biggest screens. It holds displays from 37″ to 130″ and up to
150 kg on a reinforced six-arm structure — full motion, stable through
every movement, and slim enough to sit flush to the wall. It is built for
large-format and commercial displays that standard articulating mounts
cannot carry.

Extra-large full-motion TV wall mount for 37″–130″ displays

Most full-motion wall mounts are built for mid-size TVs and cap out
around 70″. The LPC XL 01 is built for everything above that line. With a
150 kg load rating, a 37″–130″ screen range, and VESA support from
100×100 up to 1000×600 mm, it carries large-format displays
that standard articulating mounts cannot. A one-piece stamped SPCC-steel
wall plate and a reinforced six-arm structure keep heavy screens stable
through every tilt, swivel, and extension — without sag or flex.

Compatible TV sizes

With a 37″–130″ range and a 150 kg load rating, the LPC XL 01 fits every
common large-format TV size — from a 55-inch living-room display to a
100-inch home-cinema or commercial panel. Typical TVs weigh well under
the 150 kg limit, leaving a wide safety margin at every size.

Always check your TV’s VESA mounting pattern and weight against the
specifications below before installation.

LPC XL 01 features and heavy-duty engineering

Holds screens standard mounts can’t

A 150 kg load rating and 37″–130″ screen range handle large-format and
commercial displays well beyond the capacity of typical full-motion
mounts.

Reinforced six-arm structure

A 40×25 mm six-arm design distributes weight across more contact
points than conventional dual-arm mounts, a meaningful upgrade in
stability and load safety.

Wide reach, full articulation

660 mm of extension with a 120° swivel and +5° to −8°
tilt lets the screen angle toward any seat, then return flush to the
wall.

Ultra-slim, flush-to-wall profile

A 52 mm shallow-groove design keeps the TV close to the wall for a clean,
built-in look, with no bulky gap behind a large display.

One-piece stamped steel wall plate

A 5 mm SPCC-grade steel wall plate is stamped as a single piece — no
seams, no welds, no flex points — for a secure anchor under heavy load.

Precision shaft with adjustable damping

A 25 mm seamless solid steel shaft with adjustable damping holds position
without tilt or deformation, so a heavy screen stays where it is set.

LPC XL 01 technical specifications

Installation and wall requirements

The LPC XL 01 carries a heavy load, so the wall and fixings matter as
much as the mount. Before installation, confirm:

• Wall strength — the wall must support the combined
  weight of the mount and a fully loaded screen, with margin. Solid
  masonry or concrete is preferred; stud or partition walls usually need
  additional reinforcement.
• VESA match — confirm the TV’s VESA pattern falls
  within 100×100 mm to 1000×600 mm.
• Clearance — allow for the 52–660 mm extension range
  and 120° swivel so the screen moves freely.

Sliding adjustment plates simplify alignment. Tono recommends two people
for the final lift of very large or heavy screens, as a safety
precaution.

Where the LPC XL 01 fits

Living rooms with 85″+ displays

Full motion plus a flush profile suits large home-cinema screens that
angle toward seating, then sit clean against the wall.

Conference rooms and boardrooms

A 150 kg rating and VESA support to 1000×600 mm cover large
commercial and digital-signage panels.

Retail, hospitality and digital signage

Heavy-duty load capacity and a seamless steel plate suit high-traffic
installations where display safety is non-negotiable.

Frequently asked questions